telnetd (8)
NAME
telnetd - DARPA TELNET protocol serverSYNOPSIS
telnetd [-BeUhkln ] [-D debugmode ] [-S tos ] [-X authtype ] [-a authmode ] [-r lowpty-highpty ] [-u len ] [-debug ] [-L /bin/login ] [-y ] [port ]DESCRIPTION
The telnetd command is a server which supports the DARPA standard TELNET virtual terminal protocol. Telnetd is normally invoked by the internet server (see inetd(8)) for requests to connect to the TELNET port as indicated by the /etc/services file (see services(5)). The -debug option may be used to start up telnetd manually, instead of through inetd(8). If started up this way, port may be specified to run telnetd on an alternate TCP port number.The telnetd command accepts the following options:
- -a authmode
-
This option may be used for specifying what mode should
be used for authentication.
Note that this option is only useful if
telnetd
has been compiled with support for the
AUTHENTICATION
option.
There are several valid values for
authmode
- debug
- Turns on authentication debugging code.
- user
- Only allow connections when the remote user can provide valid authentication information to identify the remote user, and is allowed access to the specified account without providing a password.
- valid
- Only allow connections when the remote user can provide valid authentication information to identify the remote user. The login(1) command will provide any additional user verification needed if the remote user is not allowed automatic access to the specified account.
- other
- Only allow connections that supply some authentication information. This option is currently not supported by any of the existing authentication mechanisms, and is thus the same as specifying -a valid
- otp
- Only allow authenticated connections (as with -a user and also logins with one-time passwords (OTPs). This option will call login with an option so that only OTPs are accepted. The user can of course still type secret information at the prompt.
- none
- This is the default state. Authentication information is not required. If no or insufficient authentication information is provided, then the login(1) program will provide the necessary user verification.
- off
- This disables the authentication code. All user verification will happen through the login(1) program.
- -B
- Ignored.
- -D debugmode
-
This option may be used for debugging purposes.
This allows
telnetd
to print out debugging information
to the connection, allowing the user to see what
telnetd
is doing.
There are several possible values for
debugmode
- options
- Prints information about the negotiation of TELNET options.
- report
- Prints the options information, plus some additional information about what processing is going on.
- netdata
- Displays the data stream received by telnetd
- ptydata
- Displays data written to the pty.
- exercise
- Has not been implemented yet.
- -e
- require encryption to be turned on (in both direction) by the client and disconnects if the client tries to turn the encryption off (in either direction).
- -h
- Disables the printing of host-specific information before login has been completed.
- -k
- -l
- Ignored.
- -n
- Disable TCP keep-alives. Normally telnetd enables the TCP keep-alive mechanism to probe connections that have been idle for some period of time to determine if the client is still there, so that idle connections from machines that have crashed or can no longer be reached may be cleaned up.
- -r lowpty-highpty
- This option is only enabled when telnetd is compiled for UNICOS It specifies an inclusive range of pseudo-terminal devices to use. If the system has sysconf variable _SC_CRAY_NPTY configured, the default pty search range is 0 to _SC_CRAY_NPTY otherwise, the default range is 0 to 128. Either lowpty or highpty may be omitted to allow changing either end of the search range. If lowpty is omitted, the - character is still required so that telnetd can differentiate highpty from lowpty
- -S tos
- -u len
- This option is used to specify the size of the field in the utmp structure that holds the remote host name. If the resolved host name is longer than len the dotted decimal value will be used instead. This allows hosts with very long host names that overflow this field to still be uniquely identified. Specifying -u0 indicates that only dotted decimal addresses should be put into the utmp file.
- -U
- This option causes telnetd to refuse connections from addresses that cannot be mapped back into a symbolic name via the gethostbyaddr(3) routine.
- -X authtype
- This option is only valid if telnetd has been built with support for the authentication option. It disables the use of authtype authentication, and can be used to temporarily disable a specific authentication type without having to recompile telnetd
- -L pathname
- Specify pathname to an alternative login program.
- -y
- Makes telnetd not warn when a user is trying to login with a cleartext password.
Telnetd operates by allocating a pseudo-terminal device (see pty(4)) for a client, then creating a login process which has the slave side of the pseudo-terminal as stdin stdout and stderr Telnetd manipulates the master side of the pseudo-terminal, implementing the TELNET protocol and passing characters between the remote client and the login process.
When a TELNET session is started up, telnetd sends TELNET options to the client side indicating a willingness to do the following TELNET options, which are described in more detail below:
DO AUTHENTICATION WILL ENCRYPT DO TERMINAL TYPE DO TSPEED DO XDISPLOC DO NEW-ENVIRON DO ENVIRON WILL SUPPRESS GO AHEAD DO ECHO DO LINEMODE DO NAWS WILL STATUS DO LFLOW DO TIMING-MARK
The pseudo-terminal allocated to the client is configured to operate in ``cooked'' mode, and with XTABS and CRMOD enabled (see tty(4)).
Telnetd has support for enabling locally the following TELNET options:
- "WILL ECHO"
- When the LINEMODE option is enabled, a WILL ECHO or WONT ECHO will be sent to the client to indicate the current state of terminal echoing. When terminal echo is not desired, a WILL ECHO is sent to indicate that telnetd will take care of echoing any data that needs to be echoed to the terminal, and then nothing is echoed. When terminal echo is desired, a WONT ECHO is sent to indicate that telnetd will not be doing any terminal echoing, so the client should do any terminal echoing that is needed.
- "WILL BINARY"
- Indicates that the client is willing to send a 8 bits of data, rather than the normal 7 bits of the Network Virtual Terminal.
- "WILL SGA"
- Indicates that it will not be sending IAC GA go ahead, commands.
- "WILL STATUS"
- Indicates a willingness to send the client, upon request, of the current status of all TELNET options.
- "WILL TIMING-MARK"
- Whenever a DO TIMING-MARK command is received, it is always responded to with a WILL TIMING-MARK
- "WILL LOGOUT"
- When a DO LOGOUT is received, a WILL LOGOUT is sent in response, and the TELNET session is shut down.
- "WILL ENCRYPT"
- Only sent if telnetd is compiled with support for data encryption, and indicates a willingness to decrypt the data stream.
Telnetd has support for enabling remotely the following TELNET options:
- "DO BINARY"
- Sent to indicate that telnetd is willing to receive an 8 bit data stream.
- "DO LFLOW"
- Requests that the client handle flow control characters remotely.
- "DO ECHO"
- This is not really supported, but is sent to identify a 4.2BSD telnet(1) client, which will improperly respond with WILL ECHO If a WILL ECHO is received, a DONT ECHO will be sent in response.
- "DO TERMINAL-TYPE"
- Indicates a desire to be able to request the name of the type of terminal that is attached to the client side of the connection.
- "DO SGA"
- Indicates that it does not need to receive IAC GA the go ahead command.
- "DO NAWS"
- Requests that the client inform the server when the window (display) size changes.
- "DO TERMINAL-SPEED"
- Indicates a desire to be able to request information about the speed of the serial line to which the client is attached.
- "DO XDISPLOC"
- Indicates a desire to be able to request the name of the X windows display that is associated with the telnet client.
- "DO NEW-ENVIRON"
- Indicates a desire to be able to request environment variable information, as described in RFC 1572.
- "DO ENVIRON"
- Indicates a desire to be able to request environment variable information, as described in RFC 1408.
- "DO LINEMODE"
- Only sent if telnetd is compiled with support for linemode, and requests that the client do line by line processing.
- "DO TIMING-MARK"
- Only sent if telnetd is compiled with support for both linemode and kludge linemode, and the client responded with WONT LINEMODE If the client responds with WILL TM the it is assumed that the client supports kludge linemode. Note that the [-k ] option can be used to disable this.
- "DO AUTHENTICATION"
- Only sent if telnetd is compiled with support for authentication, and indicates a willingness to receive authentication information for automatic login.
- "DO ENCRYPT"
- Only sent if telnetd is compiled with support for data encryption, and indicates a willingness to decrypt the data stream.
FILES
- /etc/services
- /etc/inittab
- (UNICOS systems only)
- /etc/iptos
- (if supported)
SEE ALSO
telnet(1), login(1)STANDARDS
- RFC-854
- TELNET PROTOCOL SPECIFICATION
- RFC-855
- TELNET OPTION SPECIFICATIONS
- RFC-856
- TELNET BINARY TRANSMISSION
- RFC-857
- TELNET ECHO OPTION
- RFC-858
- TELNET SUPPRESS GO AHEAD OPTION
- RFC-859
- TELNET STATUS OPTION
- RFC-860
- TELNET TIMING MARK OPTION
- RFC-861
- TELNET EXTENDED OPTIONS - LIST OPTION
- RFC-885
- TELNET END OF RECORD OPTION
- RFC-1073
- Telnet Window Size Option
- RFC-1079
- Telnet Terminal Speed Option
- RFC-1091
- Telnet Terminal-Type Option
- RFC-1096
- Telnet X Display Location Option
- RFC-1123
- Requirements for Internet Hosts -- Application and Support
- RFC-1184
- Telnet Linemode Option
- RFC-1372
- Telnet Remote Flow Control Option
- RFC-1416
- Telnet Authentication Option
- RFC-1411
- Telnet Authentication: Kerberos Version 4
- RFC-1412
- Telnet Authentication: SPX
- RFC-1571
- Telnet Environment Option Interoperability Issues
- RFC-1572
- Telnet Environment Option
BUGS
Some TELNET commands are only partially implemented.Because of bugs in the original 4.2 BSD telnet(1), telnetd performs some dubious protocol exchanges to try to discover if the remote client is, in fact, a 4.2 BSD telnet(1).
Binary mode has no common interpretation except between similar operating systems (Unix in this case).
The terminal type name received from the remote client is converted to lower case.
Telnetd never sends TELNET IAC GA (go ahead) commands.